Board connections for Power Switch/Power LED/IDE LED/Reset
To fit a three-pin Power-LED connector on the two pins on the board, you must either cut the connector in half vertically and rotate the two pieces 90 degrees, or move one of the connector pins in the...
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
yeah that's how I did it- I just cut the PWR LED in half with a sharp razor blade and shaved the two new plugs a bit so they'd fit better. turned 'em around and done.why rotate 90 degrees? that's a...
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
About the 90 degrees:It's just for people who don't have the time for "shaving" the two new pieces down so they fit side-by-side with the same orientation they had to begin with. You can just rotate...
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
doh! of course.should've thought of that...:-)
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
kewl man,thanks i just couldn't figure it out so i left it off on the machine i just built, pain in the ass is that wife turns it off all the time thinking she is turning it on, just cut it!!! never...
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
Do all the switches/LEDs have to be connected to the FPI connector for the machine to work? cos ive tried the power switch in every possible place (alone) and it wont work.What can i do?
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
Quote: Do all the switches/LEDs have to be connected to the FPI connector for the machine to work? No, only the power switch need to be connected for the board to boot up on a minimal setup. You...
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
Hi Again.When i had the power switch connected to pins 6 and 8, and i turned the machine on, the athlon fan span for about a second, then stopped.The fault is not that of the PSU (as i have tried...
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
If you are absolutely sure the power supply is powerful enough, and that the board is not grounded with the case, yes, it must be faulty.
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
Thank you all soooo much just been head scrathching for half an hour on this one!!
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
Greetings everyone:My friend is having a problem with his K7S5A system. The original K7S5A v3.1 he had which had the SIS7012 soundchip on it was working fine except it hangs on idle so he decided to...
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
You guys rock. We've been trying to figure this out for DAYS. Whoever wrote that manual should be shot.Thank you, thank you, thank you.
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
Hi i need some help, this is my first computer thatI'm building myself, my questions is for the board conections how do i know which one is the positive and which one is the negative. I think the...
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
Hello LTDifferent case manufacturers use different rules for coloring the positive/negative wire, so you will have to just try connecting the Power LED and IDE LED connector one way and reverse them...
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
If you look carefully at the connectors at the ends of the wires, on one side you will see a little triangle. That triangle marks the postive side.BTW, I just built my system yesterday..it was a...
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
Let's be honest.Why bother fitting the HD LED or any of the other connections.I've been running mine for 9 months now and have no idea when the hard disk is accessing and don't really need a little...
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
I just switched cases this morning and now I can not get my comp to power up. I think I had the Power LED in the wrong place. I did not fry my board or anything, did I? I have seen the configurations...
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
My case contains no connector labelled "power" (or anything similar). But, it has two "reset" switch connectors. Am I right to assume that one of these is the power switch. Must be, I suppose. One of...
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
I lied, sorry. I've actually connected it to pins 6 and 8.
View ArticleRe: Board connections for Power Switch/Power LED/IDE LED/Reset
the pins in the three pin connector can be moved without slicing & dicing the connector.Oken mentioned it in his first post but perhaps could have explained better.when looking at the connector...
View Article
